Amorphization under fracture surface in hydrogen-charged and low- temperature tensile-tested austenitic stainless steel

ABSTRACT

The microstructure just below the fracture surface in hydrogen-charged stable austenitic SUS 316L stainless steel, which was subjected to a low strain rate tensile test at ?70°C, was studied by a combination of the focused-ion-beam method and transmission electron microscopy. An amorphous region with a chemical composition almost identical to that of the polycrystalline region was found under the lath-like structure on the fracture surface, although no deterioration of tensile properties by hydrogen appeared. In the amorphous region, band-like regions with wavy contrasts were observed, which were often accompanied by cracks at the boundaries. The presence of the amorphous region with band-like regions implies that amorphization occurred due to high-density vacancies accompanied by agglomerations of excess vacancies in the hydrogen-charged SUS 316L stainless steel that was tensile-tested at low temperatures.     

Static and dynamical ageing processes at room temperature in a Fe25Ni0.4C virgin martensite: effect of C redistribution at the nanoscale

The work-hardening behaviour of virgin martensitic steel has been investigated in a strictly un-aged state and after various ageing conditions. At room temperature (RT), the un-aged alloy shows astonishing tensile performances (ultimate tensile stress?=?1600?MPa/uniform elongation?=?15%) but unexpected serrations. These serrations can be suppressed by static ageing (at RT or higher) while maintaining the initial work-hardening rate (ageing at RT). Parallel investigations using atom probe tomography reveal that the distribution of carbon at the atomic scale evolves from purely homogeneous for virgin martensite to partly segregated at a very fine scale (5–10?nm) after static ageing. This particular mechanical behaviour can therefore be associated with a very local decrease in available carbon in solid solution due to redistribution and segregations on defects (nanotwins) that occurs rapidly, even after few days at RT.     

Hydrogen-induced cold cracking in heat-affected zone of low-carbon high-strength steel

The Y-groove cracking test by submerged arc welding was employed to study the susceptibility of a low-carbon high-strength steel to hydrogen-induced cold cracking (HICC). The morphology of hydrogen cracks was observed using an electron probe microscope. The results showed that the heat-affected zone (HAZ) has a higher susceptibility to HICC than the weld metal and that increasing heat input can improve the HICC resistance of the weldment. The intergranular microcracking is the main HICC mode at the lowest heat input condition, accompanied with some transgranular microcracks attached to complex inclusions. In combination with phase transformation behaviour in sub-zones, the effect of the phase transformation sequence is proposed to try to illustrate the fact that the fine-grained HAZ has higher probability of hydrogen cracking than the coarse-grained HAZ owing to the occurrence of hydrogen enrichment in the fine-grained HAZ after the transformation.     

The orientation and temperature dependences of dislocation velocity in Ni 3 Al single crystals

The average velocities of screw dislocations in Ni 3 Al single crystals have been directly measured as a function of resolved shear stress (RSS) and orientation in the temperature domain of the flow stress anomaly using the etch-pit technique. The velocity was found to be extremely sensitive to the RSS in all cases. In contrast with ordinary metals, the screw dislocation velocities in Ni 3 Al show anomalous behaviour; under a constant RSS, the velocities decrease dramatically with increasing temperature. Furthermore, the velocities and the tension-compression asymmetry of the velocities depend on the orientation of applied stress.     

GP zone formation without quenched-in vacancies in Al–12 wt% Mg alloy

Dissolution of GP zones, formed in aged Al–12?wt%?Mg alloy at ?15 and 24°C, occurs during primary dilatometric and calorimetric tests, but the effect disappears after secondary tests, at low heating and cooling rates (1–2°C/min). After a?new holding at the above temperatures, GP zones again form and β and β′ phases precipitate. The results suggest the formation of GP zones without the presence of quenched-in vacancies.     

钢板组及外固定架组治疗严重胫骨骨折疗效分析

探讨并分析严重胫骨骨折的手术方式。2003年9月-2010年12月我院收治的86例严重胫骨骨折进行随机分组治疗,外固定架组39例,钢板组47例,分析两组并发症及骨折愈合时间。结果86例患者均进行随访,随访时间7个月～28个月,平均10．3个月,钢板组并发症多,骨折愈合时间短,外固定架组愈合时间长。严重胫骨骨折临床多见,应根据其类型选择合理的钢板或外固定架进行治疗固定,使患者获得最佳效果。     

Effects of cementite morphology on short-fatigue-crack propagation in binary Fe–C steel

The effects of cementite morphology on short-fatigue-crack propagation were investigated by subjecting smooth steel specimens to rotating-bending fatigue tests. Intergranular and transgranular cementite precipitation steels free of other phases were prepared through heat treatments. In the intergranular cementite precipitation steel, short-fatigue-crack propagation was decelerated at the grain boundaries, and accelerated in the grain interiors. In contrast, the transgranular precipitation steel showed the deceleration of the crack propagation in the grain interiors but not in the vicinity of the grain boundaries.     

Formation of prismatic loop alignments in crystals deformed in single slip

In γ-TiAl deformed at room temperature in single slip, prismatic loops ar often organized in a staircase-like configuration, called strings whose generation by cross-slip is facilitated by the dislocation tendency to form screw locks as described recently by Grégori and Veyssière. The present letter is aimed at showing that strings may be encountered in virtually any crystal provided that the two impinging dislocations exhibit significantly different velocities. The crossslip annihilation mechanism of crossed dislocations considered by Tetelman is revisited and shown to evolve into a configuration significantly distinct from that originally predicted.     

Evolution of grain-boundary character distribution during iterative processing of an austenitic stainless steel

The present article deals with the analysis of grain-boundary character distribution (GBCD) and microstructural characteristics after iterative processing of austenitic stainless steel, AISI 316L. The steel was subjected to iterative cold reduction and subsequent annealings. After an initial decrease in the fraction of Σ3 boundaries, the number of these increases in subsequent steps. The results relate the importance of iterative processing and the mechanism of obtaining a higher fraction of Σ3 boundaries.     

On the enhancement of wear resistance of tool steels by cryogenic treatment

The present article aims to resolve the debate on the degree of benefit of processing tool or die steels by cryogenic treatment. This has been done by measuring transition loads for quenched and tempered die steel with and without cryogenic treatment. The wide range of reported degrees of improvement of wear resistance by cryotreatment is explained by the operative modes and mechanisms of sliding wear considering the wear rate ratio of conventionally treated to cryotreated steels on a two-dimensional map.