Computer-aided analysis of grain-boundary connectivity of B10 copper-nickel alloys

A numerical calculation method based on the angle in a triple junction composed of a random grain boundary is proposed to predict the connectivity and stability of a grain boundary in a B10 copper-nickel alloy. The grain-boundary connectivity and its effect on corrosion resistance are studied combining computer-aided analysis with electrochemical impedance testing. The results show that the prediction of corrosion resistance using a grain-boundary connectivity numerical method is consistent with immersion experimental results. The B10 alloy exhibited the best corrosion resistance after cold rolling with a 9% reduction rate. The relationship between the grain-boundary characteristics and corrosion resistance is well established using the numerical method to quantify the grain-boundary connectivity. A higher connective frequency and a low proportion of grain-boundary angles between 60° and 180° in the triple junction is detrimental to corrosion resistance of the B10 alloy.     

Enhancement of hardening and thermal resistance of Mg–Sn-based alloys by addition of Cu and Al

Mg–Sn-based alloys are considered as a promising precipitation-hardening system for applications at elevated temperatures, but the hardening effect is not satisfactory owing to sluggish nucleation and rapid coarsening of the major Mg₂Sn lath precipitates. In this study, Cu and Al are added to a Mg–6Sn–1Mn base alloy. The age-hardening response and the microstructures of these modified alloys have been investigated and are compared to that of the base alloy. The additional elements are found to bring several beneficial effects to the alloys for applications at elevated temperatures. Firstly, a eutectic structure consisting of strong intermetallic phases, i.e. Mg₂Cu in the Mg–6Sn–1Mn–2Cu alloy and Al_0.93Cu_1.07Mg in the Mg–6Sn–1Mn–2Cu–2Al alloy, remains stable along the grain boundaries after solution and ageing heat treatments. Secondly, the precipitate density has been increased significantly and the precipitate size has been refined remarkably during ageing at 200?°C. Moreover, the growth of the precipitates is inhibited remarkably during the over-ageing period. Therefore, the age-hardening response and over-ageing resistance are notably improved.     

Deformation of nanograined Ni–60Co alloy with low stacking fault energy

The evolution of deformation texture in a Ni–60Co alloy with low stacking fault energy and a grain size in the nanometre range has been investigated. The analyses of texture and microstructure suggest different mechanisms of deformation in nanocrystalline as compared to microcrystalline Ni–60Co alloy. In nanocrystalline material, the mechanism responsible for texture formation has been identified as partial slip, whereas in microcrystalline material, a characteristic texture forms due to twinning and shear banding.     

Fracture mechanism of a coarse-grained magnesium alloy during fracture toughness testing

The fracture mechanism during fracture toughness testing has been investigated on a coarse-grained magnesium alloy, with an average grain size of ～50 µm, and a low fracture toughness. The results show that {1012}-type deformation twins are formed at the crack tip and many dislocations pile up on these boundaries. The accumulated strains at these boundaries become the origin of fracture; i.e. cracks propagate along these boundaries between the deformation twins and the matrix.     

Microstructure and mechanical behavior of nanostructured composite Cu60Fe40 alloy

In this study, bulk nanostructured composite Cu₆₀Fe₄₀ alloy is prepared by a combustion synthesis technique. The prepared Cu₆₀Fe₄₀ alloy consists of Cu(Fe) solid solution and Fe(Cu) solid solution phases. The large-scaled compositional segregation in the Cu-rich and Fe-rich phases is not observed, respectively. A few micron-sized dendrite (Fe(Cu) solid solution) is embedded into the nanostructured matrix (Cu(Fe) solid solution). The grain size of the matrix is in the range 50–300?nm. The yield and fracture strength of the Cu₆₀Fe₄₀ alloy are 540 and 1050?MPa, respectively, and the fracture strain obtained from the compression test is about 20.9%. The Cu₆₀Fe₄₀ alloy displays notable work hardening in the compressive deformation.     

In situ characterization of the martensitic transformation temperature of NiTi shape memory alloys via instrumented microindentation

A novel, instrumented microindentation technique was successfully used to measure the temperature associated with the martensitic transformation leading to the recovery of plastic strain in a Nickel–Titanium (NiTi) shape memory alloy. Following a standard indentation cycle, the indenter was partially unloaded such that a good contact was maintained between indenter and specimen surface. The onset and finish temperature of the martensitic transformation, the associated volume contraction, and the amount of the recovered plastic deformation were determined by quantifying the indenter displacement as a function of temperature. These experiments were compared to conventional measurements of the transformation temperature by differential scanning calorimetry and compression testing.     

Bending experiments on the xi'-(Al-Pd-Mn) quasicrystal approximant

Single crystals of the quasicrystal approximant phase xi'1-(Al-Pd-Mn) were deformed at a high temperature in three-point bending geometry. Two different mechanisms of plastic deformation were observed in this phase: one based on the motion of phason lines and the other based on dislocations. Line directions and Burgers vector directions of the dislocations were determined. The relative importances of the two mechanisms are discussed as a function of the sample orientation with respect to the bending geometry.     

Tensile deformation behaviour of Zr-based glassy alloys

This paper presents a study of the deformation behaviour of a glassy phase in two Zr-based alloys, Zr₆₅Ni₁₀Cu₅Al_7.5Pd_12.5 and Zr₆₅Al_7.5Ni₁₀Pd_17.5, performed in situ in a transmission electron microscope. In contrast to the case of shear localisation and formation of 10–20 nm thick shear bands in deformed bulk glassy samples studied earlier, it is found that in thin (electron-transparent) samples the glassy phase in front of a crack deforms more homogeneously and no nanocrystallisation takes place. The reasons for such behaviour are discussed. According to the observed results, one can conclude that the studied metallic glasses can be intrinsically ductile in submicrometre-sized volumes.     

Recrystallization in a low-density low-alloy Fe–Mn–Al–C duplex-phase alloy

The recrystallization behaviour of a cold-rolled, low-density, low-alloy duplex-phase alloy (Fe–6.57Al–3.34Mn–0.18C, wt.%) has been studied. Temperature-resolved X-ray diffraction and dilatometry showed that the alloy recrystallizes at 850?°C during continuous heating. However, electron back-scattered diffraction investigations using Kernel average misorientation revealed that during annealing ferrite recrystallizes at lower temperatures while austenite remains strained up to 1200?°C. This study underlines the complexity of recrystallization of a microstructure comprising of constituents with high and low stacking fault energy.