Effect of heat treatment on the microstructure and mechanical properties of spray-formed 7055 aluminium alloy

7055 Al alloys samples were prepared by spray forming and hot-extrusion followed by two different aging treatment procedures. Their different distributions of GP zones, and nanoscale precipitates η′ (MgZn) and η (MgZn₂) are extensively investigated by transmission electron microscope (TEM). The mechanical properties, including tensile strength, Vickers hardness and elongation of both aged 7055 Al alloys, have also been measured and analysed. It is found that T6 and T76 aging treatment results in quite different microstructure and mechanical properties. The outstanding performance of the 7055 Al alloys after T6 aging treatment is attributed to nanoscale semi-coherent dispersion precipitates.     

Cooling-rate-dependent microstructure and mechanical properties of a CuZrAlAg alloy

A Cu₃₆Zr₄₈Al₈Ag₈ alloy rod with a diameter of 10 mm was fabricated using a copper-mould suction casting method. Structural characterization revealed that the rod has different microstructures along the casting direction, including a complete amorphous structure and an amorphous/crystalline composite structure with different amount of B2 CuZr phase. Nanoindentation tests showed that the hardness and the elastic modulus of the crystalline phase are lower than those of the amorphous matrix. The hardness and the elastic modulus of the amorphous matrix decrease with decreasing crystalline proportion of the alloy, while the Vickers hardness of the alloy increases with a reduction in the crystalline proportion.     

Observation of Cu nanometre scale clusters formed in Fe85Si2B8P4Cu1 nanocrystalline soft magnetic alloy by a spherical aberration-corrected TEM/STEM

Microstructure of a nanocrystalline soft magnetic Fe₈₅Si₂B₈P₄Cu₁ alloy (NANOMET^®) was investigated by the state of the art spherical aberration-corrected TEM/STEM. Observation by TEM shows that the microstructure of NANOMET^® heat treated at 738 K for 600 s which exhibits the optimum soft magnetic properties has homogeneously distributed bcc-Fe nanocrystallites with the average grain size of 30 nm embedded in an amorphous matrix. Elemental mappings indicate that P is excluded from bcc-Fe grains and enriched outside the grains, which causes to retard the grain growth of bcc-Fe crystallites. The aberration-corrected STEM-EDS analysis with the ultrafine electron probe successfully proved that Cu atoms form nanometre scale clusters inside and/or outside the bcc-Fe nanocrystallites.     

Formation of metastable phase and its influence on the solidification microstructure of highly undercooled eutectic Fe40Ni40B20 alloy

Solidification of a highly undercooled eutectic Fe₄₀Ni₄₀B₂₀ alloy melt has been studied by high-speed video in combination with an analysis of the temperature history. The metastable phase with a colony shape structure solidified primarily from the melt. DSC analysis confirmed the formation of the metastable phase. The metastable phase was re-melted, transformed or decomposed into stable phases during further solidification or cooling processes, and gave birth to the final as-solidified structures. On this basis, the effects of the metastable phase formation and transformation on evolution of the as-solidified structure is described.     

Microstructural evolutions and hardness during heat treatment of Al64Cu20Fe12Si4 quasicrystal alloy

The microhardness and microstructural characteristics and subsequent heat treatment of conventionally solidified Al₆₄Cu₂₀Fe₁₂Si₄ quasicrystal were investigated by X-ray diffractometry (XRD), scanning electron microscopy (SEM) together with energy dispersive spectroscopy (EDS), differential thermal analysis (DTA), and Vickers microhardness tester. XRD analysis indicated that the conventionally solidified samples showed a quasicrystalline icosahedral phase (i-phase) together with cubic β-AlFe, tetragonal θ-Al₂Cu, and monoclinic λ-A₁₃Fe₄ crystal phases. However, the i-phase together with cubic β-AlFe and monoclinic λ-A₁₃Fe₄ phases observed heat threaded samples. As-cast and subsequently heat-treated quasicrystal samples were measured using a microhardness test device. Vickers microindentation tests were carried out on the heat-treated quasicrystal samples with the load ranging from 1 to 500?mN at room temperature. The melting point of the i-phase was determined as 900°C by DTA examinations.     

Phonon densities of states of gamma-cerium and delta-cerium measured by time-of-flight inelastic neutron scattering

Time-of-flight inelastic neutron scattering spectra were measured on cerium metal at temperatures near the fcc (gamma)-to-bcc (delta) transition temperature. Phonon density-of-states (DOS) curves were extracted from data acquired over a wide range of momentum transfers. A large softening of the phonon DOS was found in going from gamma-cerium to delta-cerium, and this accounts for an increase in vibrational entropy of (0.71 +/- 0.05)k _B/atom. To be consistent with the latent heat of the gamma-delta transition, this increase in vibrational entropy must be accompanied by a large decrease in electronic entropy. The results not only confirm the recent discovery of a significant electronic contribution to the gamma-delta transition but also suggest that it may be twice that previously reported.     

Role of Zr on growth kinetics and microstructural evolution of the superconductor V3Ga by the bronze technique

The influence of Zr on the growth of V₃Ga is studied by a diffusion-couple technique mimicking the bronze method for superconductor production. Systematic quantitative evaluation on critical-current-density-dependent metallurgical parameters is addressed. A mixture of V₃Ga and Zr-containing phases develops at the interdiffusion zone. Smaller grains on Zr addition cause higher growth kinetics owing to grain-boundary diffusion of Ga. The grains are oriented randomly irrespective of Zr addition. Refined microstructure, second-phase, and higher growth kinetics suggest a beneficial role of Zr for the better functioning of the superconductor.     

Analyzing temporal patterns of infant sleep and negative affective behavior: a comparison between different statistical models

Objective

Variability in infant sleep and negative affective behavior (NAB) is a developmental phenomenon that has long been of interest to researchers and clinicians. However, analyses and delineation of such temporal patterns were often limited to basic statistical approaches, which may prevent adequate identification of meaningful variation within these patterns. Modern statistical procedures such as additive models may detect specific patterns of temporal variation in infant behavior more effectively.

Method

Hundred and twenty-one mothers were asked to record different behaviors of their 4–44 weeks old healthy infants by diaries for three days consecutively. Circadian patterns as well as individual trajectories and day-to-day variability of infant sleep and NAB were modeled with generalized linear models (GLMs) including a linear and quadratic polynomial for time, a GLM with a polynomial of the 8th order, a GLM with a harmonic function, a generalized linear mixed model (GLMM) with a polynomial of the 8th order, a generalized additive model, and a generalized additive mixed model (GAMM).

Results

The semi-parametric model GAMM was found to fit the data of infant sleep better than any other parametric model used. GLMM with a polynomial of the 8th order and GAMM modeled temporal patterns of infant NAB equally well, although the GLMM exhibited a slightly better model fit while GAMM was easier to interpret. Besides the well-known evening clustering in infant NAB we found a significant second peak in NAB around midday that was not affected by the constant decline in the amounts of NAB across the 3-day study period.

Conclusion

Using advanced statistical procedures (GAMM and GLMM) even small variations and phenomena in infant behavior can be reliably detected. Future studies investigating variability and temporal patterns in infant variables may benefit from these statistical approaches.